Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Horizontal Wire WoundData SheetContinued from the preceding page.2Part NumberLQW2BAS68NJ00pLQW2BAS82NJ00pLQW2BAS91NJ00pInductanceTest FrequencyRated CurrentMax. of DC ResistanceQ (min.)Test FrequencySelf Resonance Frequency (min.)68nH ±5%82nH ±5%91nH ±5%200MHz150MHz150MHz150MHz150MHz150MHz150MHz150MHz150MHz150MHz150MHz100MHz100MHz100MHz100MHz100MHz100MHz100MHz100MHz100MHz100MHz100MHz100MHz100MHz50MHz25MHz25MHz25MHz500mA400mA400mA400mA400mA400mA400mA400mA400mA400mA400mA400mA400mA400mA400mA400mA400mA350mA350mA350mA350mA310mA310mA290mA250mA230mA190mA180mA0.38ohm0.42ohm0.42ohm0.48ohm0.48ohm0.46ohm0.46ohm0.48ohm0.48ohm0.51ohm0.51ohm0.56ohm0.56ohm0.64ohm0.64ohm0.70ohm0.70ohm1.00ohm1.00ohm1.00ohm1.00ohm1.40ohm1.40ohm1.50ohm1.76ohm1.90ohm2.20ohm2.35ohm60656565656565505050505050505050504444484848484833232323500MHz500MHz500MHz500MHz500MHz500MHz500MHz250MHz250MHz250MHz250MHz250MHz250MHz250MHz250MHz250MHz250MHz250MHz250MHz250MHz250MHz250MHz250MHz250MHz100MHz50MHz50MHz50MHz1500MHz1330MHz1330MHz1330MHz1330MHz1250MHz1250MHz1100MHz1100MHz1100MHz1100MHz920MHz920MHz920MHz920MHz820MHz820MHz770MHz770MHz730MHz730MHz650MHz650MHz600MHz300MHz270MHz250MHz230MHzLQW2BAS82NG00p82nH ±2%LQW2BAS91NG00p91nH ±2%LQW2BASR10G00p100nH ±2%LQW2BASR10J00p100nH ±5%LQW2BASR11G00p110nH ±2%LQW2BASR11J00p110nH ±5%LQW2BASR12G00p120nH ±2%LQW2BASR12J00p120nH ±5%LQW2BASR15G00p150nH ±2%LQW2BASR15J00p150nH ±5%LQW2BASR18G00p180nH ±2%LQW2BASR18J00p180nH ±5%LQW2BASR22G00p220nH ±2%LQW2BASR22J00p220nH ±5%LQW2BASR24G00p240nH ±2%LQW2BASR24J00p240nH ±5%LQW2BASR27G00p270nH ±2%LQW2BASR27J00p270nH ±5%LQW2BASR33G00p330nH ±2%LQW2BASR33J00p330nH ±5%LQW2BASR39J00p390nH ±5%LQW2BASR47J00p470nH ±5%LQW2BASR56J00p560nH ±5%LQW2BASR68J00p680nH ±5%LQW2BASR82J00p820nH ±5%Operating Temperature Range (Self-temperature rise is not included): -55 to +125°C Only for refl ow soldering.c Q-Frequency Characteristics (Typ.)200c Inductance-Frequency Characteristics (Typ.)10000820nH2.8nH150Inductance (nH)1000330nH10091nH18nH91nH10047nH18nH108.2nH2.8nHQ508.2nH330nH820nH110100Frequency (MHz)100047nH100000110100Frequency (MHz)100010000Continued on the following page.oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.!Note:1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifi cations are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.2. This datasheet has only typical specifi cations because there is no space for detailed specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.2012.5.10http://www.murata.com/
Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Horizontal Wire WoundData SheetContinued from the preceding page.3c !Caution/Notice!Caution (Rating)Do not use products beyond the rated current asthis may create excessive heat.NoticeSolderability of Tin plating termination chip might bedeteriorated when low temperature soldering profi lewhere peak solder temperature is below the Tin meltingpoint is used. Please confi rm the solderability of Tinplating termination chip before use.oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design.!Note:1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifi cations are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.2. This datasheet has only typical specifi cations because there is no space for detailed specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.2012.5.10http://www.murata.com/
因篇幅问题不能全部显示，请点此查看更多更全内容