MA5616注册配置方法
外网登陆地址：220.167.183.220 用户名:huawei 密码：huawei123 AG用户名：root 密码：mduadmin OLT用户名：root 密码：jkzx@0979或者admin
以下地址为例：管理地址：135.201.8.2 管理VLAN：4000 宽带VLAN：2979（内标签201-232） 语音VLAN：200 语音IP:10.67.192.2
一、 OLT 配置
1、 创建并在上行口透传VLAN
Vlan 200 smart
Vlan 4000 smart
Port vlan 200 0/20 0
2、 查看自动发现的ONU //在onu加电链路通情况下
GEM_48JU_MA5680T#display ont autofind all
--------------------------------------------------------------------------
序列号 : 1
框/槽/端口 : 0/1/0 //此处为OLT发现ONU设备所在的框/槽/端口
ONT MAC : 5C4C-A916-23A8 //发现onu设备的MAC地址
密码 : 00000000000000000000000000000000
逻辑标识 : pmc
校验码 : sierra
生产厂商ID : HWTC
ONT型号 : 5616 //设备型号
ONT软件版本 : V8R308 C01
ONT硬件版本 : MA5616
ONT自动发现时间 : 2012-08-11 16:30:40+08:00
--------------------------------------------------------------------------
3、 进入相对应的业务板添加ONU
GEM_48JU_MA5680T(config)#INTerface EPon 0/1
MA5680T(config-if-epon-0/1)#ONT COnfirm 0 MAc-auth
5C4C-A916-23A8 SNMP ont-lineprofile-id 32 desc \"HW-1\" //用MAC注册ONU
可以被添加的ONT数目: 1, 成功数目: 1
端口号 :0, ONT号 :3 // 0 为PON口号，3 为ONUID号
MA5680T(config-if-epon -0/1)#ont ipconfig 0 3 ip adress 135.201.8.2 mask 255.255.255.0 gatway 135.210.8.1 mang-vlan 4000
MA5680T(config-if-epon-0/1)#Quit
4、 做虚业务：
MA5680T(config)# service-port vlan 4000 epon 0/1/0 ont 3 multi-service user-vlan 4000
MA5680T(config)# service-port vlan 2979 epon 0/1/0 ont 3 multi-service user-vlan 2979
MA5680T(config)# service-port vlan 200 epon 0/1/0 ont 3 multi-service user-vlan 200
二、 ONU配置
1、 查看单板信息：
MA5616(config)#display board 0
-------------------------------------------------------------------------
槽号 板名称 状态 扣板0 扣板1 在线状态
-------------------------------------------------------------------------
0 H831CCUB 主用正常 EP1A ASDA
1 H838ASRB 待确认
2 H838ASRB 待确认
3 H835ADLE 待确认
4
5 H831PAIA 正常
-------------------------------------------------------------------------
2、 确认单板：
MA5616(config)#board confirm 0
0 框 5 槽单板已经确认
MA5616(config)#display board 0
-------------------------------------------------------------------------
槽号 板名称 状态 扣板0 扣板1 在线状态
-------------------------------------------------------------------------
0 H831CCUB 主用正常 EP1A ASDA
1 H838ASRB 正常 //语音业务板
2 H838ASRB 正常
3 H835ADLE 正常 //宽带业务板
4
5 H831PAIA 正常
-------------------------------------------------------------------------
3.创建透传VLAN：
vlan 2979 smart //宽带业务vlan
vlan 200 smart //语音业务vlan
port vlan 2979 0/1 0
port vlan 200 0/1 0
4.设置宽带业务VLAN属性为是staking属性
5、宽带业务配置
添加速率模板E:\\常用资料脚本\\格尔木电信IP网管.txt
MA5616(config)# MUlti-service-port Vlan 2979 POrt 0/3 0-31 Vpi 0 Vci 35 Rx-cttr 6 Tx-cttr 6 //批量添加需业务
It will take several minutes, and console may timeout, please use command
idle-timeout to set time limit
Are you sure to create service virtual port(s)? (y/n)[n]:Y
The number of total board in this operation: 1
The number of total service virtual port in this operation: 32
Creating start...
Creating end:
The number of total service virtual port which need be created: 32
The number of total service virtual port which have been created: 32
MA5616(config)#stacking label vlan 2979 baselabel 201 //批量添加内标签
It will take several minutes, and console may be timeout, please use command idle-timeout to set time limit
Are you sure to continue? (y/n)[n]:y
The total of service virtual port(s) in this operation: 32
The total of service virtual port(s) which could be labeled: 32
Now begin to label these service virtual port(s), please wait ...
0 service-port(s) have been processed until now.
16 service-port(s) have been processed until now.
32 service-port(s) have been processed until now.
The total of service virtual port(s) which could be labeled: 32
The total of service virtual port(s) which have been labeled successfully: 32
MA5616(config)#
5、 添加语音业务：
(config)#interface vlanif 200 //起三层接口
(config-if-vlanif200)#ip address 10.67.191.2 24 //地址为语音地址
(config-if-vlanif200)#quit
(config)#voip //添加voip
(config-voip)#ip address media 10.67.191.2 10.67.191.1 //添加媒体地址
(config-voip)#ip address signaling 10.67.191.2 //添加信令地址
(config-voip)#quit
(config)#interface h248 0 //创建h.248接口
Are you sure to add MG interface?(y/n)[n]:y
(config-if-h248-0)#if-h248 attribute mgip 10.67.191.2媒体语音地址 mgport 2944 transfer udp code
text primary-mgc-ip1 10.67.5.53软交换地址 primary-mgc-port 2944 secondary-mgc-ip1 10.67.7.53 备用软交换地址secondary-mgc-port 2944 start-negotiate-version 1 profile-index 6 mg-media-ip1 10.67.191.2
(config-if-h248-0)#mg-software parameter 13 1 // 配置数图为最大匹配
(config-if-h248-0)#reset coldstart //复位h248接口
Are you sure to reset MG interface?(y/n)[n]:y
(config-if-h248-0)#
Reset MG interface 0 success!
config-if-h248-0)#quit
(config)#esl user //添加窄带用户
(config-esl-user)#mgpstnuser batadd 0/2/1 0/2/31 0 terminalid 100
telno 8716655
(config-esl-user)#quit
6、保存数据
(config)# save
因篇幅问题不能全部显示，请点此查看更多更全内容