CISCO Catalyst 4003 的配置

CISCO Catalyst 4003 的配置 Enter password: Console> enable

Enter password:

Console> (enable) set system name 4003-ER-F1 System name set.

4003-ER-F1> (enable) set system location 1st Floor Equipment Room

System location set.

4003-ER-F1> (enable) set system contact sysadmin@bigcorp.com System contact set.

4003-ER-F1> (enable) set time 04/30/1999 9:45:00 Fri Apr 30 1999, 09:45:00

4003-ER-F1> (enable) set password Enter old password: Enter new password: Retype new password: Password changed.

4003-ER-F1> (enable) set enablepass Enter old password: Enter new password: Retype new password: Password changed.

4003-ER-F1> (enable) set banner motd % 4003-ER-F1 (Catalyst 4003) Access Restricted %

MOTD banner set

4003-ER-F1> (enable) set interface sc0 10.10.1.20/24 Interface sc0 IP address set.

4003-ER-F1> (enable) set ip route default 10.10.1.1 Route added.

4003-ER-F1> (enable) set ip dns server 10.10.10.100 10.10.10.100 added to DNS server table as primary server. 4003-ER-F1> (enable) set ip dns domain bigcorp.com Default DNS domain name set to bigcorp.com 4003-ER-F1> (enable) set ip dns enable DNS is enabled

4003-ER-F1> (enable) set vtp domain BigCorp mode client VTP domain BigCorp modified

4003-ER-F1> (enable) set module name 1 Supervisor

Module name set.

4003-ER-F1> (enable) set module name 2 Gig Uplinks Module name set.

4003-ER-F1> (enable) set port flowcontrol 2/1-2 send off Ports 2/1-2 flow control send administration status set to off (ports will not send flowcontrol to far end)

4003-ER-F1> (enable) set port flowcontrol 2/1-2 receive off Ports 2/1-2 flow control receive administration status set to off (ports will not allow far end to send flowcontrol) 4003-ER-F1> (enable) set port negotiation 2/1-2 enable Ports 2/1-2 negotiation enabled

4003-ER-F1> (enable) set port name 2/1-2 GEC 802.1Q Trunk Ports 2/1-2 name set.

4003-ER-F1> (enable) set port channel 2/1-2 desirable Port(s) 2/1-2 channel mode set to desirable.

4003-ER-F1> (enable) set trunk 2/1 desirable dot1q Port(s) 2/1-2 trunk mode set to desirable. Port(s) 2/1-2 trunk type set to dot1q.

4003-ER-F1> (enable) set module name 3 Gig Server Links Module name set.

4003-ER-F1> (enable) set port name 3/1-2 Corporate Server Ports 3/1-2 name set.

4003-ER-F1> (enable) set port name 3/3 DevEng Server Port 3/3 name set.

4003-ER-F1> (enable) set port name 3/4 QA Server Port 3/4 name set.

4003-ER-F1> (enable) set port flowcontrol 3/1-4 send desired Ports 3/1-4 flow control send administration status set to desired (ports will send flowcontrol to far end if far end supports it) 4003-ER-F1> (enable) set port flowcontrol 3/1-4 receive desired Ports 3/1-4 flow control receive administration status set to desired (ports will allow far end to send flowcontrol if far end supports it) 4003-ER-F1> (enable) set port channel 3/1-2 off Port(s) 3/1-2 channel mode set to off.

4003-ER-F1> (enable) set port channel 3/3-4 off Port(s) 3/3-4 channel mode set to off. 4003-ER-F1> (enable) set trunk 3/1-4 off Port(s) 3/1-4 trunk mode set to off.

4003-ER-F1> (enable) set spantree portfast 3/1-4 enable

Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution.

Spantree ports 3/1-4 fast start enabled. 4003-ER-F1> (enable) set vlan 10 3/1-2 VLAN 10 modified. VLAN 1 modified. VLAN Mod/Ports ---- ----------------------- 10 2/1-2 3/1-2

4003-ER-F1> (enable) set vlan 20 3/3 VLAN 20 modified. VLAN 1 modified. VLAN Mod/Ports ---- ----------------------- 20 2/1-2 3/3

4003-ER-F1> (enable) set vlan 40 3/4 VLAN 40 modified. VLAN 1 modified. VLAN Mod/Ports ---- ----------------------- 40 2/1-2 3/4

4003-ER-F1> (enable)